DXi T10 Physical Characteristics

The following tables provide dimensions and other physical characteristics of the DXi T10 system components:

Parameter

Specification
Chassis

1U Rackmount

W x H x D: 17.2" (437 mm) x 1.7" (43 mm) x 23.5" (597 mm)

60 lbs (27.2 kg)
Drives

2.5" NVMe (15 TB SSD) hot swap drives (6 for DXi T10-60, 10 for DXi T10-120, DXi T10-240 and DXi T10-480)
Cooling 4 cm cooling fans (6)
Memory DDR4,32 GB,RDIMM,3200 MT,2Rx4 (16)
Motherboard H12SSW-NTR: proprietary form factor 13.4" x 12.29" (340mm x 312mm)
Power Supply 750W redundant power supply (2)
Processor Single AMD EPYC™ 7002 Series Processor

 

Usable Capacity¹

DXi T10-60

  • From 15 TB to 60 TB

DXi T10-120

  • From 30 TB to 120 TB

DXi T10-240

  • From 60 TB to 240 TB

DXi T10-480

  • From 120 TB to 480 TB

¹ Usable storage capacity can be upgraded at any time after purchase by adding a storage capacity upgrade license to enable installed hardware capacity, or by adding additional hardware capacity to the system. For information about upgrade options, see DXi T10 Capacity Upgrade or contact your Quantum sales representative.
 
Ethernet Cable Drops

The following Ethernet connections are available for NAS or OST connectivity, replication, and remote management.

(2 x 10 GBase-T ports.) - RJ-45 ports.Can be used for system management or for NAS, Application Specific, OST, and replication connectivity.

(4 to 12 x 10/25 GbE ports) - (SFP28 optical or DAC copper) for NAS, Application Specific, OST, and replication connectivity.

(2 to 4 x 100 GbE ports) - (SFP28 optical or DAC copper) for NAS, Application Specific, OST, and replication connectivity.

Note: For Cisco 5000 Series Data Center Class switches, Quantum recommends using the approved 5 meter Twinax cable type that is shipped with the DXi T10 system. Otherwise, Quantum recommends using optical (SFP+) connectivity.

Note: The 10/25 GbE Copper (DAC) cable options that Quantum provides do not support all switches. Some switch vendors allow only their cables to be used to connect the switches they produce. Please note the supported switches during the purchase-configuration process, and if the Twinax cables supplied by Quantum are not compatible with your switch, please obtain the vendor’s compatible Twinax cables from your switch vendor. Be sure to have these available before the system installation takes place.

 
Ethernet Cables

10/25 GbE Optical Cable (10/25 GbE Ethernet Card)

40/100 GbE MTO/MTP Optical Cable (100 GbE Ethernet Card)

10/25 GbE Copper (DAC) Cable (10/25 GbE Ethernet Card)

40/100 GBe Copper (DAC) Cable (100 GbE Ethernet Card)

CAT6 Cable

Fibre Channel Drops Up to 6 Fibre Channel connections for path-to-tape (PTT) or VTL data transfer.
Power Outlets Node - 2 USA type 3-prong power outlets (Nema 5-15) or 2 C13 type 3-prong power outlets (IEC320 C13).

Expansion Module (each) - 2 USA type 3-prong power outlets (Nema 5-15) or 2 C13 type 3-prong power outlets (IEC320 C13).

 

Interfaces

VTL backup target: 64 partitions maximum

NAS backup target: 128 shares maximum (NFS or CIFS)

Note: NFS version: DXi supports NFSv3 in sync mode only. NFSv4 and async mode are not currently supported.

Note: Samba version: 4.5.3

OST backup target: 100 storage servers maximum

Caution: To safeguard backups and to avoid potential data loss in the event of a power outage, Quantum recommends that you connect the DXi T10 to an uninterruptible power supply (UPS) with a minimum UPS capacity rating that meets the power requirements stated above.

Each DXi T10 chassis contains two 750 watt power supply units (PSU) for redundancy.

Parameter

Specification
Power Cable C13/C14 (2)
AC Input Voltages 100-240 VAC
Rated Current 8.5 - 6.0 A
Rated Input Frequency 50-60 Hz
Rated Output Power 750W
Rated Output Voltages +3.3V (25A), +5V (25A), +12V (700W: 58A at 100V-140V, 750W: 62A at 180V-240V), -12V (0.6A), +5Vsb (3A)