Expansion Cards – Logical Port Numbers and Slots

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender, aiWARE for Xcellis and Embedded (DAE) systems.

The following logical port numbers are applicable to the Expansion Cards:

Caution: Individual FC ports should not be configured on the FC switch for access to both disk and tape. FC ports should be zoned for use with either disk OR tape, not both.

The following applies to all systems supported by this Documentation Center, which include Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), Xcellis Foundation, and all aiWARE for Xcellis systems.

Figure 1: Logical/Physical Port numbers for the 4-port 1 GbE Network Daughter Card/Embedded NIC

Note: em4 is bonded by default into Bond 0 (metadata) along with em3 during installation, but the bond may be broken and em4 used for something other than the metadata bond after installation if desired.

Note: There is no GUI on Xcellis Workflow Extender (R630) systems, so em2 does not provide GUI access for that product.

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), Xcellis Foundation,and all aiWARE for Xcellis systems.

Figure 2: Logical/Physical Port numbers for the 4-port 1 GbE NIC in Slot 1

Figure 3: Logical/Physical Port numbers for the 2-port 10 GbE NIC in Slot 1

Figure 4: Logical/Physical Port numbers for the 2-port 10 GbE baseT NIC in Slot 1

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 5: Logical/Physical Port numbers for the 4-port 1 GbE NIC in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), Xcellis Foundation, and all aiWARE for Xcellis systems.

Figure 6: Logical/Physical Port numbers for the 2-port 10 GbE NIC in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 7: Logical/Physical Port numbers for the 2-port 10 GbE baseT NIC in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 8: Logical/Physical Port numbers for the 2-port 40 GbE NIC in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 9: Logical/Physical Port numbers for the 2-port 56 Gb InfiniBand HCA in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 10: Logical/Physical Port numbers for the 4-port 8 Gb Fibre Channel Card in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 11: Logical/Physical Port numbers for the 2-port 16 Gb Fibre Channel Card in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 12: Logical/Physical Port numbers for the 4-port 16 Gb Fibre Channel Card in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), Xcellis Foundation, and all aiWARE for Xcellis systems.

Note: SFP+ Transceivers not used in Xcellis Foundation systems. Instead, Xcellis FoundationXcellis Foundation uses Twinax cables.

Figure 13: Logical/Physical Port numbers for the 2-port 10 GbE NIC in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 14: Logical/Physical Port numbers for the 2-port 10 GbE baseT NIC in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 15: Logical/Physical Port numbers for the 2-port 40 GbE NIC in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 16: Logical/Physical Port numbers for the 2-port 56 Gb InfiniBand HCA in Slot 2

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Foundation, and all aiWARE for Xcellis systems.

Note: SFP+ Transceivers not used in Xcellis Foundation systems. Instead, Xcellis FoundationXcellis Foundation uses Twinax cables.

Figure 17: Logical/Physical Port numbers for the 2-port 10 GbE NIC in Slot 2. (Provides iSCSI connections for QXS chassis.)

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 18: Logical/Physical Port numbers for the 4-port 16 Gb Fibre Channel Card in Slot 3

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 19: Logical/Physical Port numbers for the 4-port 8 Gb Fibre Channel Card in Slot 3

The following applies to Xcellis Workflow Director (R630), Artico (R630), Xcellis Workflow Extender (R630), and aiWARE for Xcellis Embedded (DAE) systems.

Figure 20: Logical/Physical Port numbers for the 2-port 16 Gb Fibre Channel Card in Slot 3

The following applies to Xcellis Workflow Extender (R630) systems only.

Figure 21: Logical/Physical Port numbers for the 2-port 32 Gb Fibre Channel Card in Slot 3